Orbea

Occam 29 S10

Orbea's presence within the peloton is undeniable. Conversely, though, in the world of knobby tires, this respected Spanish company is quickly gaining ground as it transfers a wealth of carbon expertise into fresh designs. Born in the rugged mountains of the Basque Country, the Occam 29 S10 represents the height of Orbea's abilities.

Orbea's line of 105mm-rear-wheel travel, carbon 29ers, like the 26-inch wheeled Occam Carbon, use Orbea's Silver grade carbon fiber . Basically, this is where the front triangle is molded as one piece, with no joints. This process keeps the weight low while concurrently increasing strength. Also similar to the 26-inch Occam, the seatstays are made of aluminum. And since the seatstays on any frame are subject to compressive forces, and carbon fiber is weakest in compression, this is an intelligent material substitution.

However, despite these design parallels, the Occam 29 Carbon is not simply tweaked regurgitation of the 26-inch Occam. Instead, it was developed as an all-new platform using Orbea's Advanced Dynamics technology. From the earliest stages of design, Orbea analyzed the Occam 29's performance in a computer simulation with virtual riders on board. Why is this so important? The variable and dynamic forces exerted onto a mountain bike by the rider are an integral part of how the bike accelerates, stops, and tracks over bumps. So, it makes sense that Orbea considered these forces in its design process from the get-go. Of course, when a prototype was ready, Orbea replaced virtual riders with real ones for exhaustive on-trail testing.

Orbea's results lead it to use a single-pivot suspension design with a Diamond Link to control shock rate. And while, in some mountain biking circles, the phrase 'single-pivot' is synonymous with 'unrefined' or even 'archaic,' the actuality is quite the opposite. Single-pivot suspension designs are still relevant and often preferred. When designed well, they're tough, lively, predictable, and, when mated with a good shock, easy to set up and tune. The Occam 29's main pivot is located on the seat tube, above the bottom bracket to strike a superb balance between pedaling efficiency for climbs and sprints, with plushness for freewheeling descents.

One oft-lamented characteristic of single-pivot full-suspension bikes is brake squat -- or better known as the suspension compression that occurs when you grab a handful of rear brake. This brake-induced compression is felt by the rider as stiffening of the rear suspension. So, to resist brake squat, the Occam suspension design incorporates a concentric pivot at the 142 x 12mm rear axle.

As a result, the brake caliper is not wholly beholden to follow the arching path of the chainstays, which form the main levers of the swingarm, as the suspension cycles. That freedom of movement results in more active suspension under braking, producing a ride quality similar to that of a complex four-bar suspension system, or a single-pivot bike with an aftermarket brake floater. End result? With the rear brake on, the bike will stutter less over bumps and have improved traction.

Controlling this Occam's suspension movement is a remotely operated Fox CTD with the Climb, Trail, and Descend damper that makes adapting your tune to the terrain as easy as flicking a handlebar switch. This is combined with a F29 FIT CTD fork with the same, intuitive dampening adjustments and handle bar remote. Additionally, both are equipped with Kashima for durability and smoothness. At 100mm of travel, this fork gives the S10 a 70 degree head tube angle, which is ideal for cross-country racing. And when looking at a 29er's geometry, another measurement we always examine closely is chainstay length -- we like what we see with the Occam 29. At 17.5 inches, the chainstays are sufficiently short enough to allow nimble handling and confident traversing of switchbacks.

Orbea took the time to cleanly route the Occam's cables by running the rear brake and rear derailleur housing along the top of the down tube, while securing them with bolt-on guides. And the front derailleur cable is internally routed through the frame to shelter it from contaminating muck. Those cables control an XTR front and rear derailleur. The rear cassette is a Shimano XTR with an 11-36T spread that's teamed up with an XTR 24/38T crankset for a simple 2x10 drivetrain that hits all of the right gears. The S10 rides on Mavic Crossmax SLR wheels wrapped in 2.2in-wide Geax AKA XC tires. And stopping it is a set of XTR Trail hydraulic disc brakes. Finishing off the Occam 29 S40X build is an alloy Race Face Turbine handlebar, steam, and Next SL seatpost.

The Orbea Occam 29 S10 is available in the sizes Small, Medium, and Large and in the colors Carbon/blue and Carbon/red. Please note that all Orbea frames have a lifetime warranty against manufacturing defect.